Home

Toyota Workshop

GSIC - Global Service Information Center

ROOF HEADLINING > REMOVAL

for Preparation Click here



1. PRECAUTION (w/ Navigation System for HDD)

NOTICE:
After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.



2. REMOVE REAR NO. 2 FLOOR BOARD


    B227787E01

  1. Disengage the 2 guides <A> as shown in the illustration.

  1. Disengage the 3 guides <B> and remove the rear No. 2 floor board.



3. REMOVE REAR DECK FLOOR BOX

  1. Remove the rear deck floor box.



4. REMOVE REAR NO. 3 FLOOR BOARD


    B227791

  1. Disengage the 2 guides and remove the rear No. 3 floor board.



5. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



6. REMOVE FRONT DOOR SCUFF PLATE LH


    B227761

  1. Disengage the 10 claws and remove the front door scuff plate LH.



7. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    B227764

  1. Remove the clip.

  1. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.



8. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B227768

  1. Remove the front door opening trim weatherstrip LH.



9. REMOVE FRONT PILLAR GARNISH LH


    B257021

  1. When removing the front pillar garnish LH, cover the shaded part in the illustration with a piece of cloth so that the interior parts will not be damaged.



    B257024E01

  1. Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
    Text in Illustration 
    *1
    		Front Pillar Garnish Clip

    HINT:
    Make the front pillar garnish LH hang down from the front pillar garnish clip.



    B257019E01

  1. Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and remove it from the front pillar garnish LH.

    NOTICE:
    1. Front pillar garnish clips are reusable if they are not removed from the vehicle and have no damage.
    2. Replace the front pillar garnish clips with new ones if they are removed from the vehicle.

    HINT:
    Tape the needle-nosed pliers tip before use.
    Text in Illustration 
    *1
    		Protective Tape

  1. Disengage the 3 guides.



    B257022E01

  1. Disengage the claw while pressing the shaded part in the illustration in the direction indicated by the arrow (1).

  1. Remove the front pillar garnish LH by pulling it in the direction indicated by the arrow (2) in the illustration.



    B227780E01

  1. Protect the curtain shield airbag assembly.
    Text in Illustration 
    *1
    		Adhesive Tape
    *2
    		Protective Cover
    *3
    		Curtain Shield Airbag Assembly

    1. Cover the airbag with a cloth or piece of nylon and secure the ends of the cover with tape as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



10. REMOVE REAR DOOR SCUFF PLATE LH


    B227766

  1. Disengage the 7 claws and remove the rear door scuff plate LH.



11. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


    B227770

  1. Remove the rear door opening trim weatherstrip LH.



12. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)


    B221487

  1. Disengage the 3 claws and remove the lap belt outer anchor cover.



13. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    B221489

  1. Remove the bolt and disconnect the floor end of the front seat outer belt assembly.



14. REMOVE CENTER PILLAR LOWER GARNISH LH


    B227782

  1. Disengage the 2 claws and 2 clips, and remove the center pillar lower garnish LH.



15. REMOVE CENTER PILLAR GARNISH LH


    B227784

  1. Remove the screw.

  1. Using a clip remover, disengage the clip.

  1. Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar garnish LH and remove the center pillar garnish LH.



16. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure described for the LH side.



17. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



18. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure described for the LH side.



19. REMOVE FRONT PILLAR GARNISH RH

HINT:
Use the same procedure described for the LH side.



20. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure described for the LH side.



21. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure described for the LH side.



22. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:
Use the same procedure described for the LH side.



23. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



24. REMOVE CENTER PILLAR LOWER GARNISH RH

HINT:
Use the same procedure described for the LH side.



25. REMOVE CENTER PILLAR GARNISH RH

HINT:
Use the same procedure described for the LH side.



26. REMOVE REAR SEAT CUSHION ASSEMBLY


    B229992E01

  1. Disengage the 2 front hooks of the seat cushion from the vehicle body as shown in the illustration.
    Text in Illustration 
    *1
    		100 mm (3.94 in.) or less
    *2
    		Hook
    *3
    		Guide

    NOTICE:
    Follow the instructions below carefully as the cushion frame deforms easily.


    1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

    2. Repeat the above procedure for the other hook.

  1. Disengage the 2 guides of the seat cushion from the seatback.

  1. Remove the rear seat cushion assembly.



27. REMOVE REAR SIDE SEATBACK ASSEMBLY LH


    B230041

  1. Remove the bolt.



    B230042

  1. Disengage the 2 guides and remove the rear side seatback assembly LH as shown in the illustration.



28. REMOVE REAR SIDE SEATBACK ASSEMBLY RH


    B230044

  1. Remove the bolt.



    B230045

  1. Disengage the 2 guides and remove the rear side seatback assembly RH as shown in the illustration.



29. REMOVE UPPER INSTRUMENT PANEL ASSEMBLY

  1. Remove the upper instrument panel assembly (Click here).



30. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

  1. Remove the tonneau cover assembly.



31. REMOVE REAR NO. 4 FLOOR BOARD


    B227789

  1. Disengage the guide and remove the rear No. 4 floor board.



32. REMOVE DECK FLOOR BOX LH


    B227790

  1. Remove the clip.

  1. Disengage the 2 guides and remove the deck floor box LH.



33. REMOVE REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY


    B227792

  1. Disengage the 2 claws and 2 clips, and remove the rear No. 1 floor board sub-assembly.



34. REMOVE REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY


    B227793

  1. Disengage the claw and 2 clips, and remove the rear No. 2 floor board sub-assembly.



35. REMOVE REAR NO. 1 FLOOR BOARD


    B227794

  1. Remove the bolt.

  1. Disengage the 2 claws and 2 clips, and remove the rear No. 1 floor board.



36. REMOVE DECK TRIM SERVICE HOLE COVER


    B227795

  1. Disengage the 2 claws and 3 guides, and remove the deck trim service hole cover.



37. REMOVE REAR DECK TRIM COVER


    B227796

  1. Disengage the 4 claws and 4 guides, and remove the rear deck trim cover.



38. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)


    B227798

  1. Remove the 2 bolts.

  1. Disengage each guide and remove the 2 luggage hold belt striker assemblies.



39. REMOVE TONNEAU COVER HOLDER CAP (for LH Side)


    B227799E01

  1. Using a screwdriver, disengage the claw and remove the tonneau cover holder cap.
    Text in Illustration 
    *1
    		Protective Tape

    HINT:
    Tape the screwdriver tip before use.



40. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

  1. Remove the screw.

  1. Disengage the 7 claws and 2 clips.



  1. Disconnect the connector and remove the deck trim side panel assembly LH.


    B227804



41. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH


  1. Disengage the 9 clips and remove the roof side inner garnish assembly LH.


    B227806



42. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)

HINT:
Use the same procedure described for the LH side.



43. REMOVE TONNEAU COVER HOLDER CAP (for RH Side)

HINT:
Use the same procedure described for the LH side.



44. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

  1. Remove the screw.



  1. Disengage the 7 claws and 2 clips, and remove the deck trim side panel assembly RH.


    B227803



45. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



46. REMOVE INNER REAR VIEW MIRROR COVER (w/ EC Mirror)


    B229499

  1. Disengage the 2 claws and slide the inner rear view mirror cover as shown in the illustration.



    B229500

  1. Disengage the 6 claws and remove the inner rear view mirror cover.



47. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)


    E189311

  1. Disconnect the rain sensor cover as shown in the illustration.

  1. Disengage the 2 claws and remove the rain sensor cover.



48. REMOVE ROOF TOP MOULDING


    B227832

  1. Using moulding remover B, disengage the 3 claws and 2 clips, and remove the roof top moulding.



49. REMOVE MAP LIGHT ASSEMBLY (w/o Sliding Roof)


    E189673

  1. Disengage the 4 clips and 2 guides as shown in the illustration.

  1. Disconnect the connector and remove the map light assembly.



50. REMOVE MAP LIGHT ASSEMBLY (w/ Sliding Roof)


    E189671

  1. Disengage the 4 clips and 2 guides as shown in the illustration.

  1. Disconnect the connector and remove the map light assembly.



51. REMOVE NO. 1 ROOM LIGHT ASSEMBLY


    E189683E01

  1. Using a screwdriver wrapped with protective tape, disengage the 4 claws and remove the No. 1 room light lens.
    Text in Illustration 
    *1
    		Protective Tape



    E189685E01

  1. Using a screwdriver wrapped with protective tape, disengage the 2 claws and 2 guides, and remove the 2 No. 1 room light covers.
    Text in Illustration 
    *1
    		Protective Tape



    E189687E01

  1. Using a screwdriver wrapped with protective tape, disengage the 4 claws and disconnect the No. 1 room light assembly as shown in the illustration.
    Text in Illustration 
    *1
    		Protective Tape



    E189689

  1. Using a screwdriver, disengage the 4 claws and disconnect the room light switch base from the No. 1 room light assembly.



52. REMOVE FRONT ASSIST GRIP ASSEMBLY


    B229260E01

  1. Using a clip remover, disengage the 4 claws.

    NOTICE:
    Do not forcibly pry the assist grip covers to prevent them from being deformed.

    HINT:
    1. Gently pry on the assist grip covers as shown in the illustration to remove them.
    2. Tape the clip remover tip before use.

  1. Pull off the 2 assist grip covers by hand.



    B229261

  1. Disengage the 2 clips and remove the front assist grip assembly.

  1. Remove the 2 clips from the vehicle body.

    HINT:
    Use the same procedure for the other front assist grip.



53. REMOVE REAR ASSIST GRIP ASSEMBLY


    B229262E01

  1. Using a clip remover, disengage the 4 claws.

    NOTICE:
    Do not forcibly pry the assist grip covers to prevent them from being deformed.

    HINT:
    1. Gently pry on the assist grip covers as shown in the illustration to remove them.
    2. Tape the clip remover tip before use.

  1. Pull off the 2 assist grip covers by hand.



    B229263

  1. Disengage the 2 clips and remove the rear assist grip assembly.

  1. Remove the 2 clips from the vehicle body.

    HINT:
    Use the same procedure for the other rear assist grip.



54. REMOVE VISOR BRACKET COVER LH


    B227807

  1. Using moulding remover B, disengage the 3 claws and remove the visor bracket cover LH.



55. REMOVE VISOR ASSEMBLY LH


    B227811

  1. Disengage the 2 clips and remove the visor assembly LH.



56. REMOVE VISOR BRACKET COVER RH

HINT:
Use the same procedure described for the LH side.



57. REMOVE VISOR ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



58. REMOVE VISOR HOLDER


    B211697E01

  1. Turn the visor holder approximately 45° and pull it out as shown in the illustration.

  1. Disengage the 2 claws and remove the visor holder.

    HINT:
    Use the same procedure for the other visor holder.



59. REMOVE ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)

  1. w/ Rain Sensor:

    1. Disengage the 2 clamps and disconnect the rain sensor connector.

  1. w/ EC Mirror:

    1. Disengage the 2 clamps and disconnect the inner rear view mirror connector.

  1. Disengage the 3 clamps and disconnect the connector from the front pillar RH.

  1. Disengage the clamp and disconnect the connector from the rear pillar RH.

  1. Disengage the 4 clamps from the front pillar LH.

  1. Disconnect the 2 No. 1 roof wire connectors from the connector holder.



  1. Remove the 5 clips.


    B227817E01


    Text in Illustration 
    *1
    		w/ EC Mirror
    		*2
    		w/ Rain Sensor



    B227856

  1. Remove the roof headlining assembly from the vehicle through the back door.

    NOTICE:
    Do not damage the roof headlining assembly or body interior.



60. REMOVE ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)

  1. w/ Rain Sensor:

    1. Disengage the 2 clamps and disconnect the rain sensor connector.

  1. w/ EC Mirror:

    1. Disengage the 2 clamps and disconnect the inner rear view mirror connector.

  1. Disengage the 3 clamps and disconnect the connector from the front pillar RH.

  1. Disengage the clamp and disconnect the connector from the rear pillar RH.

  1. Disengage the 4 clamps from the front pillar LH.

  1. Disconnect the 2 No. 1 roof wire connectors from the connector holder.



  1. Remove the 3 clips.


    B227813E01


    Text in Illustration 
    *1
    		w/ EC Mirror
    		*2
    		w/ Rain Sensor



  1. Disengage the 6 fasteners.


    B227814



    B227855

  1. Remove the roof headlining assembly from the vehicle through the back door.

    NOTICE:
    Do not damage the roof headlining assembly or body interior.