FRONT SEAT CUSHION HEATER (for Manual Seat) > INSTALLATION

for Preparation Click here

1. Using hog ring pliers, install 11 new hog rings.
   

   NOTICE:

   1. Be careful not to damage the cover.
      
   2. When installing the hog rings, take care to minimize wrinkles as much as possible.
      

2. Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 2 new hog rings.
   

   NOTICE:

   1. Be careful not to damage the cover.
      
   2. When installing the hog rings, take care to minimize wrinkles as much as possible.
      

1. Engage each hook as shown in the illustration.
   
   

   
   
   
   

2. Engage the 2 hooks as shown in the illustration.
   

3. Using hog ring pliers, install 3 new hog rings
   

   NOTICE:

   1. Be careful not to damage the cover.
      
   2. When installing the hog rings, take care to minimize wrinkles as much as possible.
      

4. for Passenger Side:
   
   

   
   
   

   1. Engage the guide and install the belt warning occupant detection sensor.
      

   
   
   

   2. Engage the 3 clamps.
      

   3. Connect the connector.
      

5. Engage the 4 hooks.
   

6. w/ Seat Heater System:
   
   

   
   
   

   1. Engage the clamp.
      

   
   
   

   2. Fasten the front seat cushion cover with pad as shown in the illustration.
      

   3. Connect the connector.
      

7. w/ Lumber support:
   
   

   
   
   

   1. Engage the 4 clamps.
      

   
   
   

   2. Engage the 3 clamps and connect the connector.
      

8. Engage the hook and install the front seat cushion cover with pad.
   

1. Engage the 2 claws and install the front seat cushion inner shield.
   

1. Install the front seat inner belt assembly with the nut.
   

   Text in Illustration 

   *1	Protruding Part

   Torque:

   42 N*m{ 428 kgf*cm , 31 ft.*lbf }

   NOTICE:

   Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

2. Connect each connector.
   

3. Engage each clamp.
   

1. w/ Lumber Support:
   
   

   
   
   

   1. Disengage the 5 clamps.
      

   2. Connect the connector.
      

2. Engage the clip and 2 claws.
   

3. Install the front seat cushion shield assembly with the screw.
   

1. Install the vertical adjusting handle with the screw.
   

1. Engage the claw and install the reclining adjuster release handle.
   

1. Place the front seat assembly in the cabin.
   

   NOTICE:

   Be careful not to damage the vehicle body.

2. Connect the connectors under the seat.
   

3. Temporarily install the front seat assembly with the 4 bolts.
   

4. Lift up the seat track adjusting handle and move the seat to the rearmost position.
   

5. Tighten the 2 bolts on the front side of the seat.
   

   Torque:

   37 N*m{ 377 kgf*cm , 27 ft.*lbf }

   HINT:

   Tighten the bolts in the order indicated in the illustration.

6. Lift up the seat track adjusting handle and move the seat to the foremost position.
   

7. Tighten the 2 bolts on the rear side of the seat.
   

   Torque:

   37 N*m{ 377 kgf*cm , 27 ft.*lbf }

   HINT:

   Tighten the bolts in the order indicated in the illustration.

1. Engage the claw and guide and install the inner seat track cover.
   

1. Engage the 2 claws and install the outer seat track cover.
   

1. Install the front seat headrest assembly as shown in the illustration.
   

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

1. Engage the 2 guides to install the rear No. 3 floor board.
   

1. Install the rear deck floor box.
   

1. Engage the 3 guides <A>.
   

2. Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.
   

1. During sliding operation of the front seat, check that the left and right adjusters move together smoothly and lock simultaneously.
   If the seat adjusters do not lock simultaneously, loosen the seat mounting bolts to adjust the adjuster position.
   

2. w/ Seat Heater Seat System:
   Check the seat heater operation.
   
   

   1. Turn the power switch on (IG).
      

   2. Push the seat heater switch on.
      

   3. Wait 5 minutes or more and confirm that the seat surface becomes warm.